Investigation of fabrication of gas diffusion substrate for proton exchange membrane fuel cells

The gas diffusion substrate (GDS) is essential in the proton exchange membrane fuel cells. Its fabrication techniques affect the performance significantly and are worthy of investigation. In this study, a manufacturing process of the GDS is proposed to understand the formation process of GDS and promote its structure and performance more pertinently. Different states during the preparation process, raw carbon paper, pre-curing, curing, carbonation, and graphitization, are characterized and measured. Experimental and numerical methods are employed to determine the relationships between microstructure, transport, and mechanical performance variation with the fabricating processes. The results show that its porosity, average pore size, and effective diffusivity decrease first and increase after curing. These parameters after graphitization are lower than that of the carbon paper (CP). The electrical resistivity increases dramatically while pre-curing and decreases gradually after curing, carbonation, and graphitization, and it is much reduced after graphitization. Moreover, mechanical measurement results show that both the picks of tensile strength and flexural modulus occur after curing. Its tensile strength shows little change after graphitization compared to the initial paper's. In contrast, the flexural modulus is improved significantly.     

Sustainable phenolic thermosets coatings derived from urushiol

The over-exploitation of finite fossil resources and/or the increased environmental and sustainable awareness inspire scientists and technologists to search for inexpensive alternatives from renewable chemicals. Phenol formaldehyde (PF) resins, the oldest type of synthetic polymers with good mechanical properties and heat resistance, are widely used in the production of coatings, laminates, molding compositions, and glues. Here, biobased urushiol-derived PF resins were synthesized from the alkali-catalyzed reaction between urushiol and formaldehyde. The chemical compositions and molecular structures of resole resins were characterized by carbon-13 nuclear magnetic resonance and Fourier transform infrared spectroscopy, and their curing behaviors were studied by differential scanning calorimetry. The as-prepared urushiol-derived resole resins had methylol (Ph−CH₂OH), ortho- and para-hemiformal groups (Ph−CH₂OCH₂OH), and the para−para/ortho−para/ortho−ortho links of methylene groups (Ph−CH₂−Ph), whereas the resole resins had low curing temperatures at about 100–113°C. Additionally, given the long side alkyl group moiety on the aromatic rings of urushiol, the films of cured urushiol-derived resole resins had low glass transition temperatures of 132 ± 2°C. Furthermore, the as-prepared urushiol-derived coatings exhibited excellent physical and mechanical properties.     

A comparative study on the effect of carbon-based and ceramic additives on the properties of fiber reinforced polymer matrix composites for high temperature applications

Ablative composites have been in use for thermal protection of space vehicles for decades. Carbon-phenolic composites have proven to perform exceptionally well in these applications. However with development in aerospace industry their performance needs improvement. In this field, different carbon-based and ceramic additives have been introduced into ablative composite systems. This review article gives a comparative analysis of researches done in this field in the recent past. Density, ablative, thermal and mechanical properties of ablative composites with different ultra-high temperature ceramic particles i.e. ZrSi₂, Cenosphere, nano-SiO₂, BN etc. and carbon-based nanoparticles i.e. CNTs, nano-Diamonds, Graphene oxide etc. used as additives, have been compared and discussed. Emphasis is put on carbon-phenolic composite systems although some epoxy matrix systems have also been discussed for comparison.     

Alterations in phenolic compound levels and antioxidant activity in response to cooking technique effects: A meta-analytic investigation

The aim of this study was to review prior studies that have evaluated the effects of cooking techniques on polyphenol levels and antioxidant activity in vegetables and to release a meta-analysis of the findings. Meta-analysis with a random effect model was conducted using the weighted response ratios (R*) that were calculated for each experiment. Baking (R* = 0.51), blanching (R* = 0.94), boiling (R* = 0.62), microwaving (R* = 0.54) and pressure cooking (R* = 0.47) techniques precipitated significant reductions in the polyphenol levels. Significant decreases in the antioxidant activity levels were noted after baking (R* = 0.45) and boiling (R* = 0.76), while significant increases were observed after frying (R* = 2.26) and steaming (R* = 1.52).     

Development of a difunctional oxirane and multifunctional acrylate interpenetrating polymer network composite system with antimicrobial properties

This research continued the development of a difunctional Oxirane and multifunctional Acrylate interpenetrating polymer network composite System (OASys) with antimicrobial properties. The effects of 4-Isopropyl-4′-methyldiphenyliodonium tetrakis (pentafluorophenyl) borate (Borate), hexamethylene diamine (HMDA) and N,N-dimethyl p-toluidine (DMPT) on OASys (Epalloy 5001:dipentaerythritol hexaacrylate) composite hardness, contact angle, monomer-to-polymer degree of conversion (DoC), mechanical properties, polymerization shrinkage, shrinkage stress, and antimicrobial properties were determined. Bis-GMA:TEGDMA composites were used as the control. OASys composites with 9 wt% Borate and 0.5 wt% DMPT or 1.5 wt% HMDA had comparable hardness, DoC's and polymerization shrinkages to controls, but had lower contact angles and mechanical properties. Additionally, OASys composites with 1.5 wt% HMDA had significantly less polymerization stress than controls and demonstrated significant antibacterial activity against Streptococcus mutans and Lactobacillus casei out to 3 months. With lower shrinkage stress and long-term antimicrobial activity, OASys composites look promising for increasing the clinical lifetime of dental composites, but improvements in mechanical properties are needed.     

Multivariate process trajectories for molecular description of MF thermal curing and correlation with hydrolytic stability

During curing of thermosetting resins the technologically relevant properties of binders and coatings develop. However, curing is difficult to monitor due to the multitude of chemical and physical processes taking place. Precise prediction of specific technological properties based on molecular properties is very difficult. In this study, the potential of principal component analysis (PCA) and principal component regression (PCR) in the analysis of Fourier transform infrared (FTIR) spectra is demonstrated using the example of melamine-formaldehyde (MF) resin curing in solid state. FTIR/PCA-based reaction trajectories are used to visualize the influence of temperature on isothermal cure. An FTIR/PCR model for predicting the hydrolysis resistance of cured MF resin from their spectral fingerprints is presented which illustrates the advantages of FTIR/PCR compared to the combination differential scanning calorimetry/isoconversional kinetic analysis. The presented methodology is transferable to the curing reactions of any thermosetting resin and can be applied to model other technologically relevant final properties as well.     

苯并噁嗪树脂的合成及在形状记忆聚合物中的应用研究进展

苯并噁嗪树脂作为一类新型的热固性树脂，具有分子设计性强、阻燃性能和耐腐蚀性能优异、固化时不需要强酸、无小分子放出等优点，在航空、建筑、电子等领域获得了广泛应用。本文主要介绍了苯并噁嗪单体的合成方法（溶剂法、无溶剂法和悬浮法）、降低苯并噁嗪开环聚合温度的方法（合成具有特殊基团的苯并噁嗪单体、添加催化剂）及苯并噁嗪树脂在形状记忆聚合物中的应用（与其他聚合物混合，纯苯并噁嗪化学改性），对苯并噁嗪形状记忆聚合物目前存在的问题进行了概述并对苯并噁嗪形状记忆聚合物的发展前景做出了展望。     

The activation of furfuryl alcohol polymerization by oxygen and its enhanced mechanical properties

The effect of oxygen and additional oxygen providers on furfuryl alcohol polymerization was investigated through chemical analyses and mechanical evaluation. NMR, UV–vis, Fourier transform infrared, and gas chromatography–mass spectrometry (GC–MS) results suggested that atmospheric oxygen and the further addition of an oxygen source functioned as an activator for the entire network polymerization. Interestingly, the construction of a conjugated structure on the furan linear chain, which is key to three-dimensional cross-linking, also appears to be accelerated in the presence of oxygen. Furthermore, the introduction of oxygen providers into the curing system successfully enhanced the mechanical properties of the cured furan resin.     

Distribution of vanadium and vanadyl porphyrins during fractionation of resins of heavy sulfurous oils

Features of the content and distribution of vanadium and vanadyl porphyrins in the fractions of resins, which were obtained by separation using column chromatography on silica, have been studied on heavy sulfurous oils of various deposits of the Volga–Ural basin (Russia). The difference of the vanadium and vanadyl porphyrin contents in the fractions of oils of various production complexes has been shown. Features of structural–group composition and predominant types of vanadyl porphyrins in the fractions of resins have been determined.     

Glass transition evaluation of commercially available epoxy resins used for civil engineering applications

The paper presents a study about the glass transition of commercially available epoxy resins used for structural strengthening of concrete members for instance by means of Carbon Fiber Reinforced Polymer (CFRP) strips. Prior to an experimental investigation with a dynamic mechanical analysis (DMA), an overview on differences between definitions for the glass transition temperature T_g is given. Several testing recommendations are listed in this respect. Subsequently, DMA tests on three commercially available products are presented. A first focus is put on the different evaluation methods for one specific test result. It is visible that considerable differences in the finally adapted glass transition temperature might arise if one or the other procedure is followed. Additional parameters, such as curing procedure, specimen age, temperature history, and ultimate temperature during heating are considered, too. In all the above mentioned cases, differences in the glass transition can be found. Higher specimen age, higher ultimate temperature during testing, accelerated curing, as well as a lower heating rate implicate higher glass transition temperatures, showing that the glass transition temperature is not a fixed material characteristic. In a final step, the relevance for T_g for civil engineering applications is described. The various design code provisions for defining the service temperature in structures related to T_g are presented. The overall aim of the investigation is to show that structural engineers and end users have to be aware of the different influential parameters on the final results regarding the glass transition temperature, which also highlights the need of a potential deeper product investigation in case technical data sheets lack detailed information.